PVC Injection Molding Material Supplier & Manufacturer

Polyvinyl Chloride (PVC) is one of the most versatile and cost-effective thermoplastics in injection molding, available in rigid and flexible (plasticized) forms. It offers excellent chemical resistance, inherent flame retardancy from its chlorine content, and good electrical insulation at a very low material cost. Shinzoft delivers OEM/ODM PVC injection molding for fittings, electrical boxes, cable components, and medical connectors, from DFM through mass production.

Key Properties of PVC for Injection Molding

Chemical & Corrosion Resistance

Outstanding resistance to acids, alkalis, salts, alcohols, and many industrial chemicals. This is why PVC dominates pipe, fitting, and chemical-handling parts where other plastics corrode.

Inherent Flame Retardancy

The chlorine in the molecule makes PVC self-extinguishing; it stops burning once the flame source is removed and does not drip. It meets strict fire-safety standards without added flame retardants.

Electrical Insulation

High dielectric strength and good volume resistivity make rigid PVC a reliable insulator for conduit fittings, junction boxes, cable terminations, and switchgear.

Low Cost & Formulation Range

PVC is among the cheapest engineering-grade thermoplastics. The same polymer base spans hard, structural parts and soft, rubber-like seals simply by changing the plasticizer level.

Technical Specifications of PVC

Values below refer to unfilled rigid PVC. Flexible compounds are softer and lower in modulus, with properties that shift according to plasticizer content.

PropertyTypical ValueNotes
Density1.35–1.45 g/cm³Rigid grades; flexible grades vary with plasticizer
Tensile Strength40–55 MPaRigid; flexible compounds drop to 10–25 MPa
Flexural Modulus2,400–3,000 MPaRigid; softens sharply as plasticizer is added
Heat Deflection Temp (HDT, 1.8 MPa)60–70 °CLow for a rigid plastic; limits high-temperature use
Glass Transition Temp (Tg)75–85 °CAmorphous polymer — no true melting point
Molding Shrinkage0.3–0.8 %Low and predictable; flexible grades shrink slightly more
Dielectric Strength14–20 kV/mmGood insulation for electrical housings and fittings

Applications of PVC Injection Molding

  • ✅ Plumbing & Construction: pipe fittings, valves, elbows, tees, and drainage components in rigid PVC
  • ✅ Electrical: junction boxes, conduit fittings, cable glands, and switch housings
  • ✅ Medical (flexible, medical-grade): tubing, connectors, catheter fittings, and fluid-handling parts
  • ✅ Sealing & Soft-Grip: gaskets, seals, edge trims, and weather strips in flexible PVC
  • ✅ Industrial & Consumer: handles, protective caps, and chemical-resistant housings

PVC Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / TimeUsually not required; dry 70–80 °C / 1–2 h if stored damp
Melt Temperature180–210 °C (narrow, tightly controlled window)
Mold Temperature30–60 °C
Injection Pressure60–100 MPa
Typical Cycle Time20–50 s, depending on wall thickness

Temperature control is the single most important variable in PVC molding. The processing window is narrow and close to its decomposition point: above roughly 210 °C the polymer begins shedding hydrogen chloride gas, which burns the melt, discolors the part, and attacks the screw and barrel. Hold barrel temperatures within grade limits, keep screw speed moderate to limit shear heating, shorten residence time, and vent the mold well so any trace gas escapes instead of scorching the surface. Heat stabilizers help but buy margin rather than immunity, so plan shutdowns rather than leave PVC hot in the barrel.

Design & Tooling Considerations for PVC

  • Corrosion-resistant tooling: HCl released during any thermal excursion corrodes ordinary steel. Specify stainless or plated cavities and runners, and keep surfaces clean and polished.
  • Generous flow paths: avoid sharp gates and long, thin sections that raise shear and heat. Smooth transitions reduce local overheating and burn marks.
  • Venting is mandatory: add vents at the last-fill locations so decomposition gases and trapped air escape. Poor venting shows up as burn marks and weak weld lines.
  • Modest walls and radii: PVC flows well, but thick sections trap heat and extend cooling. Use ribs to add stiffness instead of heavy walls, with generous fillets.
  • Stabilizer and grade selection: heat stabilizers are essential for processing and long-term stability. Choose rigid or flexible compound, and specify medical or food-grade versions where the part touches fluids.

PVC vs Other Injection Molding Materials

PVC's closest relatives in soft, flexible applications are the elastomers. Compared with TPE, flexible PVC is cheaper and inherently flame-retardant, but TPE has a cleaner rubber feel, better aging, and no plasticizer migration. Against TPU, PVC is far less abrasion- and oil-resistant, though it costs a fraction as much and needs no drying. Where chemical resistance, flame safety, and cost drive the decision, PVC stays practical.

Among rigid commodity plastics, PVC outruns ABS on chemical resistance and flame retardancy, but ABS is tougher and easier to process. PVC also beats most polyethylene grades on cost and flame behavior, though it gives up impact strength and a wide processing window. PVC buys chemical and fire resilience at the cost of careful process control.

Related Injection Molding Materials

Why Choose Our Factory for PVC Injection Molding

  • ISO 9001 Certified Quality: tight temperature control, in-process inspection, and full traceability from pellet lot to finished part.
  • 15+ Years of Experience: founded in 2010 in Shenzhen with 50+ molding machines and a Huizhou plant, serving 1,000+ customers.
  • Free DFM Analysis: we review wall thickness, gating, venting, and tool steel selection before cutting steel, with no minimum order quantity.
  • Fast Lead Time: most orders ship within 15 working days, backed by dedicated lines and high-volume tooling.

FAQs About PVC Injection Molding

What is the difference between rigid and flexible PVC?

Both use the same PVC base. Rigid PVC contains no plasticizer and behaves like a hard structural plastic with a tensile strength of 40–55 MPa, used for pipe fittings, valves, and electrical boxes. Flexible PVC is compounded with plasticizers that lower its modulus and make it soft and rubber-like, ideal for tubing, seals, and cable jackets.

Why is PVC so sensitive to processing temperature?

PVC starts to decompose above roughly 210 °C and releases hydrogen chloride gas, which discolors the part, weakens it, and corrodes the tooling. The 180–210 °C window is narrow, so we hold barrel temperatures tightly, keep screw speed moderate, shorten residence time, and ensure the mold vents well.

Is PVC flame retardant, and how does that work?

Yes. PVC is inherently flame retardant because chlorine makes up a large part of its molecule. Exposed to flame it self-extinguishes once the source is removed and does not drip, so it meets fire-safety requirements without the additive flame-retardant packages other plastics require. This is a major reason PVC is used for electrical and construction parts.

Is PVC suitable for medical applications?

Medical-grade flexible PVC is widely used for tubing, catheters, blood bags, and connectors. These grades use plasticizers and stabilizers selected for biocompatibility and meet USP Class VI and ISO 10993. We mold medical PVC only with certified compounds on dedicated, cleaned equipment.

Does PVC need to be dried before molding?

PVC is not hygroscopic, so it generally does not require drying, unlike nylon or TPU. If the compound has been stored in a damp environment, a short dry of 1–2 hours at 70–80 °C removes surface moisture without risking the thermal degradation that prolonged high heat would cause.

Looking for a Reliable PVC Injection Molding Supplier?

Send your drawings and service conditions — chemical exposure, temperature, and fire-safety requirements. Our engineers will recommend the right rigid or flexible PVC compound and deliver consistent production.

Shinzoft serves customers worldwide with custom PVC injection molding solutions and a full range of injection molding materials.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com