PSU (Polysulfone) Injection Molding Supplier & Manufacturer

Polysulfone (PSU) is an amber-transparent amorphous thermoplastic with a glass transition temperature of 185–190 °C, hydrolytic stability that survives 1000+ steam sterilization cycles, and inherent flame retardancy without additives. At 1.24 g/cm³ it is one of the lighter high-temperature engineering resins and offers continuous service to 150–160 °C. Common parts include reusable medical sterilization components, food-service containers, electrical insulators, and membrane filter housings. Shinzoft supplies OEM/ODM PSU injection molding from DFM and tooling through validated mass production.

Key Properties of PSU for Injection Molding

Hydrolytic Stability

PSU withstands repeated autoclave and steam exposure — well over 1000 sterilization cycles in typical service — without crazing, clouding, or embrittlement. Few transparent engineering plastics match this clarity and steam durability.

High Glass Transition

A 185–190 °C glass transition supports continuous service at 150–160 °C and an HDT above 170 °C at 1.8 MPa. Because PSU is amorphous it has no melting point and shrinks uniformly, which simplifies tight-tolerance design.

Inherent Flame Retardancy

PSU achieves UL94 V-0 on its own with low smoke output and a high limiting oxygen index, avoiding the halogenated additives that complicate medical and food-contact approvals.

Toughness & Light Weight

Notched impact strength stays high across a broad temperature range, and at 1.24 g/cm³ PSU is lighter than most high-heat resins. That toughness supports thin-wall cassettes, housings, and parts that clip together.

Technical Specifications of PSU

The values below are typical for unfilled general-purpose polysulfone. Transparent grades are standard; 30% glass-filled grades raise modulus and HDT at the cost of clarity.

PropertyTypical ValueNotes
Density1.24 g/cm³Transparent unfilled; ~1.45 with 30% glass fiber
Tensile Strength70–75 MPaUnfilled, room temperature
Flexural Modulus2,600–2,800 MPaRises above 8,000 MPa with glass fiber
Heat Deflection Temp (HDT, 1.8 MPa)170–180 °CContinuous service 150–160 °C
Glass Transition Temp185–190 °CAmorphous — no crystalline melting point
Molding Shrinkage0.6–0.8 %Low and largely isotropic
Dielectric Strength~16 kV/mmStable dielectric behavior for insulating parts

Applications of PSU Injection Molding

  • ✅ Medical Sterilization: Reusable sterilization containers and trays, instrument organizers, suction canisters, and surgical device housings.
  • ✅ Food Service & Membrane Housings: Transparent food-service containers, food-processing sight glasses, and filter housings and end caps for water and dairy lines.
  • ✅ Electrical & Electronic: Insulators, connector bodies, circuit-breaker and relay parts, and coil formers needing V-0 rating with 150 °C service.
  • ✅ Membrane & Filtration Systems: Hollow-fiber module housings, end caps, and manifolds for hemodialysis, water treatment, and bioprocessing.
  • ✅ Automotive & Industrial: Under-hood electrical housings, sight glasses, and fluid-handling components exposed to hot water and steam.

PSU Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / Time150 °C / 3–4 h (required)
Melt Temperature330–390 °C
Mold Temperature100–160 °C
Injection Pressure70–140 MPa
Injection SpeedMedium to fast
Typical Cycle Time30–70 s, depending on wall thickness

PSU is hygroscopic and must be dried at 150 °C for three to four hours, because moisture in the melt produces splay and can trigger hydrolysis that dulls the transparent finish. Avoid melt temperatures above 400 °C: they promote thermal degradation, yellowing, and a loss of impact strength. A hot mold of 100–160 °C helps fill thin sections, reduces molded-in stress, and produces the surface finish transparent parts need. Purge between material changes to prevent cross-contamination, and avoid long residence times.

Design & Tooling Considerations for PSU

  • Shrinkage compensation: Design to 0.6–0.8% for unfilled PSU and confirm on the trial shot; amorphous shrinkage is low and consistent, so tolerance stack-up behaves predictably.
  • Stress and solvent sensitivity: Solvent contact plus residual molded-in stress causes crazing, so keep walls uniform, use generous radii, and anneal parts headed for chemically aggressive service.
  • Gate and venting design: Large, well-polished gates and effective venting reduce shear stress and help achieve the optical surface quality transparent parts require.
  • Transparent-part tooling: Polish cavities to a high finish, keep flow paths streamlined to avoid flow marks, and control mold temperature uniformity to prevent haze or weld-line read-through.
  • High-temperature tooling: Provide oil-temperature control, hardened tool steel, and hot-runner manifolds rated above the melt ceiling for the 330–390 °C process window.

PSU vs Other Injection Molding Materials

PSU is the cost-friendlier route to transparent, steam-sterilizable parts. Compared with PEI (Polyetherimide) injection molding, PSU costs less and delivers similar clarity and flame performance, but its glass transition of 185–190 °C sits about 30 °C below PEI's 217 °C, so its heat ceiling is lower. Where continuous temperatures climb toward 250 °C or a much broader chemical range is needed, PEEK injection molding is the stronger choice at higher material cost. Where transparency and toughness are needed but heat demands are modest, PC (Polycarbonate) injection molding costs considerably less and molds more easily.

Related Injection Molding Materials

  • PEI Injection Molding — amber-transparent amorphous polymer with a 217 °C glass transition and a higher heat ceiling than PSU.
  • PEEK Injection Molding — semi-crystalline performance leader with 343 °C melting point and near-universal chemical resistance.
  • PC Injection Molding — clear, high-impact resin for room-temperature parts where autoclave stability is not required.

Why Choose Our Factory for PSU Injection Molding

  • ISO 9001 Certified Quality: Our Shenzhen headquarters and Huizhou factory operate an ISO 9001 system with RoHS and REACH documentation plus PPAP for regulated programs.
  • 15+ Years of Experience: Founded in 2010, we have produced more than 30 million molded parts for over 1,000 customers across medical, food processing, and electrical work.
  • High-Temperature Process Control: More than 50 machines with oil-temperature controllers, hot-runner tooling, and scientific molding tuned to the 330–390 °C PSU window.
  • Free DFM Analysis: We review wall thickness, gating, venting, and stress concentration points before tooling, then verify optical and dimensional results with a capability study.
  • No Minimum Order Quantity & Fast Lead Time: The same tooling covers prototype and production volumes, and most orders ship within 15 working days.

FAQs About PSU Injection Molding

How many steam sterilization cycles can PSU withstand?

PSU handles well over 1000 autoclave cycles at 134 °C without losing clarity, mechanical strength, or dimensional accuracy. That hydrolytic stability is the main reason it dominates reusable medical trays, sterilization containers, and instrument housings, and it also tolerates gamma and EtO sterilization.

What is the difference between PSU and PEI?

Both are amorphous, transparent, inherently flame-retardant high-heat polymers. PSU has a 185–190 °C glass transition and continuous service to 150–160 °C, while PEI reaches 217 °C and about 170 °C continuous. PSU generally costs less and matches PEI on steam sterilization, so it is often the better value where the heat ceiling allows.

Why does PSU need drying before molding?

PSU absorbs moisture from the air, and that water flashes to steam at 330–390 °C melt temperatures, causing splay, bubbles, and surface streaks that ruin a transparent part. Dry pellets at 150 °C for three to four hours before molding and keep them covered during production.

Does PSU need flame retardant additives to meet UL94 V-0?

No. Polysulfone is inherently flame retardant and reaches UL94 V-0 on its own with low smoke generation, which keeps it free of the halogenated additives that can complicate medical and food-contact approval. Unfilled transparent grades carry the rating without loss of clarity.

How do you prevent crazing in molded PSU parts?

Crazing usually comes from residual molded-in stress combined with solvent exposure. We keep walls uniform, use generous radii, run a hot mold to reduce stress, and anneal parts intended for chemically aggressive service. Choosing the right grade and avoiding incompatible cleaning agents also extends part life.

Looking for a Reliable PSU Injection Molding Partner?

Send us your drawings with your sterilization cycle count, clarity requirements, and temperature range. You will receive a quote plus a free DFM analysis covering grade selection, gating, and stress control.

Shinzoft serves customers worldwide with custom PSU injection molding solutions, from prototype tooling to repeat production. Compare grades on our materials page.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com