PEEK Injection Molding Material Supplier & Manufacturer

Polyetheretherketone (PEEK) is a semi-crystalline thermoplastic often called the king of specialty engineering plastics. It pairs a glass transition temperature of 143 °C and a melting point of 343 °C with a continuous service temperature around 260 °C, near-universal chemical resistance, self-lubricating wear behavior, and fatigue durability. Typical parts include aerospace brackets, implant-grade medical components, semiconductor parts, downhole oil and gas tools, and premium gears and bearings. Shinzoft supplies OEM/ODM PEEK injection molding from DFM and tooling through validated mass production.

Key Properties of PEEK for Injection Molding

Extreme Temperature Capability

PEEK holds useful mechanical properties at continuous service temperatures up to 260 °C and short-term excursions above that. Its Tg sits at 143 °C and its crystalline melting point at 343 °C, so parts keep stiffness long after most engineering plastics have softened.

Chemical Resistance

PEEK resists nearly every industrial chemical, including hydrocarbon fuels, hydraulic fluids, acids, bases, and steam. Concentrated sulfuric acid is the notable exception. Low moisture uptake keeps dimensions and dielectric performance stable in wet service.

Durability & Self-Lubrication

Unfilled PEEK has a low coefficient of friction and strong fatigue resistance under cyclic load. Tribological grades with PTFE, graphite, or carbon fiber cut wear rates further, suiting bearings, bushings, and seals.

Biocompatibility & Sterilization

Implant-grade PEEK passes ISO 10993 biocompatibility testing and tolerates autoclave steam, gamma, and EtO sterilization, supporting surgical instruments, dental components, and implantable devices.

Technical Specifications of PEEK

Values below are typical for unfilled general-purpose PEEK grades. Carbon and glass fiber compounds raise modulus and HDT at the cost of elongation and impact toughness.

PropertyTypical ValueNotes
Density1.30–1.32 g/cm³Unfilled; ~1.40 with 30% carbon fiber
Tensile Strength95–100 MPaUnfilled, room temperature
Flexural Modulus3,700–4,100 MPaRigid even at elevated temperature
Heat Deflection Temp (HDT, 1.8 MPa)150–160 °CAbove 300 °C for 30% glass-fiber grades
Glass Transition / Melting Point143 °C / 343 °CSemi-crystalline; crystallinity drives properties
Molding Shrinkage1.0–1.3 %Flow direction, unfilled; grade dependent
Dielectric Strength20–24 kV/mmStable over a wide frequency range

Applications of PEEK Injection Molding

  • ✅ Aerospace: Structural brackets, clamps, cable guides, and interior hardware where weight and heat resistance both matter.
  • ✅ Medical & Implant-Grade: Sterilizable instrument handles, dental components, and implant-grade parts under project-specific regulatory review.
  • ✅ Semiconductor & Chemical Processing: Wafer handling parts, manifolds, fluid-contact fixtures, and pump components that resist aggressive chemistry.
  • ✅ Oil & Gas Downhole: Wear rings, valve seats, seals, and back-up rings for high-temperature, high-pressure wells.
  • ✅ High-End Gears & Bearings: Self-lubricating gears, bushings, thrust washers, and sliding elements replacing metal in dry or chemically exposed drives.

PEEK Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / Time150 °C / 3–4 h
Melt Temperature360–400 °C
Mold Temperature170–200 °C (high-temperature tooling)
Injection Pressure80–140 MPa
Injection SpeedMedium to fast, with adequate venting
Typical Cycle Time40–90 s, depending on wall thickness

PEEK is hygroscopic and must be dried thoroughly before processing, otherwise splay, voids, and loss of mechanical strength follow. A hot mold of 170–200 °C is essential: mold temperature governs crystallinity, and therefore strength, chemical resistance, and dimensional stability. Avoid cold slugs and stagnant melt in the barrel, since the material degrades quickly when overheated. Hardened tool steel, high-temperature controllers, and generous venting are standard requirements rather than options.

Design & Tooling Considerations for PEEK

  • Shrinkage compensation: Plan for 1.0–1.3% semi-crystalline shrinkage in unfilled grades and validate with a tooling trial, since shrinkage shifts with wall thickness, gate location, and mold temperature.
  • High-temperature tool design: Use hardened or stainless tool steel, hot-runner systems rated above 200 °C, and thermal control that keeps cavity temperature uniform to avoid warpage.
  • Uniform walls and balanced gating: Gradual thickness transitions and a balanced runner layout improve packing and reduce the internal stress that distorts thin, long parts.
  • Gate and flow-path sizing: Keep restrictive gates short and polished; avoid abrupt flow restrictions that cause jetting or premature freeze-off in a cooling cavity.
  • Wear surfaces for filled grades: Carbon and glass fiber compounds abrade tooling, so use hardened gates, polished vents, and replaceable inserts on high-wear areas.

PEEK vs Other Injection Molding Materials

PEEK sits at the top of the price and performance ladder among injection molded thermoplastics, so specify it when the application genuinely needs it. Where continuous temperatures stay below about 170 °C and chemical exposure is modest, PEI (Polyetherimide) injection molding delivers a comparable high-temperature amorphous profile at a lower material cost. When the priority is stiffness at 200 °C plus and tighter dimensional control, LCP injection molding suits thin, high-flow parts, while PPA injection molding covers many automotive under-hood duties at a fraction of PEEK pricing.

Related Injection Molding Materials

  • PEI Injection Molding — amber-transparent amorphous polymer with a 217 °C glass transition, ideal for sterilizable parts that do not need PEEK's chemical extremes.
  • PPA Injection Molding — high-temperature polyamide with 280–320 °C melting, a cost-effective route for engine-bay housings and connectors.
  • LCP Injection Molding — liquid crystal polymer with near-zero flow-direction shrinkage for ultra-thin, high-frequency parts.

Why Choose Our Factory for PEEK Injection Molding

  • ISO 9001 Certified Quality: Our Shenzhen headquarters and Huizhou factory run an ISO 9001 quality system with RoHS and REACH documentation plus PPAP support for automotive programs.
  • 15+ Years of Experience: Founded in 2010, we have delivered more than 30 million molded parts to over 1,000 customers, including high-temperature and filled grades.
  • High-Temperature Tooling In-House: More than 50 machines with hot-mold capability, oil-temp controllers, and scientific molding tuned to PEEK's narrow process window.
  • Free DFM Analysis: We review wall thickness, gating, cooling, and shrinkage compensation before cutting steel, then confirm performance with a capability study.
  • No Minimum Order Quantity & Fast Lead Time: Prototype and production volumes share the same tooling, and most orders ship within 15 working days.

FAQs About PEEK Injection Molding

Why is a hot mold required for PEEK injection molding?

PEEK is semi-crystalline, and mold temperature controls how much crystallinity develops during cooling. Molds held at 170–200 °C produce the high crystallinity behind full strength, chemical resistance, and dimensional stability. A cold mold yields a partly amorphous, brittle part.

When should I specify filled PEEK grades instead of unfilled PEEK?

Choose 30% glass or carbon fiber for higher flexural modulus, an HDT above 300 °C, or reduced creep under sustained load. Choose PTFE, graphite, or carbon tribological grades when low friction and long wear life matter more than impact toughness, as in bearings and seals.

Can PEEK parts be sterilized repeatedly?

Yes. PEEK withstands repeated autoclave steam cycles, gamma irradiation, and ethylene oxide treatment without significant loss of mechanical properties, and it resists hydrolysis during steam exposure. Implant-grade grades that pass ISO 10993 are available for regulated programs.

How do you prevent PEEK degradation during molding?

We cap melt temperature around 400 °C, avoid long residence times, keep shot size above roughly 50% of barrel capacity, and purge promptly between runs. Drying at 150 °C for 3–4 hours removes the moisture that otherwise causes splay, voids, and property loss.

Is PEEK worth the material cost compared with other high-temperature plastics?

Unfilled PEEK typically runs in the USD 80–100 per kilogram range, far above PEI, PPA, or PSU. It earns that cost where continuous service near 260 °C, near-universal chemical resistance, or implant-grade biocompatibility is required. For milder duties, PEI or PPA usually delivers adequate performance for less.

Looking for a Reliable PEEK Injection Molding Partner?

Send us your drawings along with your service temperature, chemical exposure, and validation requirements. You will get a quote and a free DFM analysis covering grade selection, gating, and shrinkage compensation.

Shinzoft serves customers worldwide with custom PEEK injection molding solutions, from prototype tooling to repeat production. Browse our full materials range to compare grades.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com