PBT Injection Molding Material Supplier & Manufacturer

PBT (polybutylene terephthalate) is a semi-crystalline engineering polyester known for fast crystallization and short cycle times, resistance to oils and chemicals, and low moisture absorption that keeps electrical properties stable. It also reaches flame-retardant UL94 V-0 ratings easily, with an HDT near 150 °C that climbs past 200 °C when glass filled. It is the workhorse for electrical connectors, relay bobbins, automotive ignition parts, motor housings, and keyboard keys. Shinzoft provides OEM/ODM PBT injection molding from DFM and tooling through validated mass production.

Key Properties of PBT for Injection Molding

Fast Crystallization, Short Cycles

PBT crystallizes quickly, so parts set fast and cycle times stay short even at moderate mold temperatures. That speed is a direct cost advantage in high-volume connector and small-part production.

Chemical & Oil Resistance

PBT withstands oils, greases, fuels, and many solvents, and it resists hydrolysis better than some polyesters. This makes it reliable around automotive fluids and industrial lubricants without stress cracking.

Stable Electrical Properties

Low moisture absorption — around 0.1–0.4% — keeps dielectric strength and insulation resistance steady across humidity and temperature swings. That stability is why PBT dominates connectors, relays, and switchgear.

Heat & Flame Resistance

Unfilled PBT reaches an HDT near 150 °C at 1.8 MPa; glass-filled grades exceed 200 °C. Flame-retardant formulations hit UL94 V-0 at 0.8 mm and thinner, often with minimal effect on mechanical strength.

Technical Specifications of PBT

The table below covers general-purpose unfilled PBT; glass-filled grades raise stiffness and heat resistance while lowering shrinkage.

PropertyTypical ValueNotes
Density1.30–1.32 g/cm³Unfilled grade
Tensile Strength50–60 MPa30% GF raises to 120–140 MPa
Flexural Modulus2,200–2,600 MPa30% GF reaches 8,000–9,000 MPa
Notched Izod Impact30–50 J/mNotch sensitive; GF grades lower
Heat Deflection Temp (HDT, 1.8 MPa)~150 °CGF grades above 200 °C
Melting Point / Tg~220–225 °C / 40–50 °CSemi-crystalline polyester
Molding Shrinkage1.2–2.0 %Unfilled; 0.3–0.8% with 30% GF
Dielectric Strength16–24 kV/mmStable under humidity
Water Absorption (24 h)0.1–0.4 %Low for a polyester

Applications of PBT Injection Molding

  • ✅ Electrical Connectors: plugs, sockets, terminal blocks, board-to-board connectors, wire harness connectors
  • ✅ Relay & Switchgear Parts: relay bobbins, coil formers, switch housings, contact carriers
  • ✅ Automotive Ignition & Sensors: ignition coil housings, sensor covers, lamp sockets, fuse boxes
  • ✅ Electric Motor Components: motor end caps, brush holders, stator insulation, fan blades
  • ✅ Consumer Electronics: keyboard keys and frames, appliance control knobs, pump housings, valve bodies
  • ✅ Industrial Parts: gears, pump components, housing covers, precision mechanical parts

PBT Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / Time120 °C / 2–4 h
Melt Temperature240–270 °C
Mold Temperature60–90 °C (up to 100 °C for finish)
Injection Pressure60–100 MPa
Typical Cycle Time15–40 s (short due to fast setup)

PBT must be dried before molding: wet resin hydrolyzes at melt temperature and quickly turns brittle. Dry at 120 °C for 2–4 hours and keep the melt within 240–270 °C. PBT is notch sensitive, so parts should be designed with generous radii and molded without excessive shear at gates. Fast crystallization allows short cycles, but raising mold temperature toward 90–100 °C improves surface finish and crystallization uniformity on cosmetic parts.

Design & Tooling Considerations for PBT

  • Shrinkage planning: unfilled PBT shrinks roughly 1.2–2.0%, considerably more than PC or ABS. Glass-filled grades drop to 0.3–0.8% but shrink differently along and across flow, so account for directional values.
  • Round the corners: PBT is notch sensitive. Sharp internal corners raise the risk of brittle cracking, so specify generous radii on load-bearing features.
  • Warpage control: glass-filled grades warp when flow balance is poor. Use balanced runners, uniform wall thickness, and adequate cooling on both faces.
  • Gate size: use adequate gate diameters to avoid high shear that degrades the melt and lowers impact strength; avoid pin-point gates on thick sections.
  • Venting: vent the cavity well — fast filling traps gas that causes burns and short shots if it cannot escape.

PBT vs Other Injection Molding Materials

PBT and PET are close chemical relatives, but PBT crystallizes faster, which shortens cycle times and gives a wider processing window — the main reason it edges out PET for precision electrical parts. When a part needs PBT's chemical resistance plus the toughness of PC, PC-PBT alloy adds impact strength at low temperature for bumper and tool-housing duty. For connectors that must survive continuous temperatures above 200 °C, high-temperature nylons such as PPA extend beyond what standard PBT can hold.

Related Injection Molding Materials

Why Choose Our Factory for PBT Injection Molding

  • ISO 9001 Certified Quality: strict drying and temperature control, RoHS and REACH compliance, and dimensional inspection suited to tight connector tolerances.
  • 15+ Years of Experience: operating since 2010, we have molded 30M+ parts for 1,000+ customers in automotive, electrical, and industrial sectors.
  • Free DFM Analysis: we review shrinkage, wall thickness, and gate placement before cutting steel, which prevents warpage and brittleness problems on molded parts.
  • Fast Lead Time & No MOQ: 50+ machines in Shenzhen and Huizhou, most orders delivered within 15 working days, with no minimum order quantity.

FAQs About PBT Injection Molding

What is the difference between PBT and PET?

Both are semi-crystalline polyesters, but PBT crystallizes much faster, giving shorter cycle times and a wider processing window. PET offers higher stiffness, hardness, and surface finish. For precision electrical connectors and parts that need fast, repeatable molding, PBT is usually the better fit; PET suits parts that value stiffness and dimensional stability.

Does PBT need to be dried before molding?

Yes. PBT is moisture sensitive, and wet resin hydrolyzes at melt temperature, which lowers molecular weight and makes parts brittle. Dry at 120 °C for 2–4 hours and target a moisture content below 0.04% before processing. Skipping the dry cycle is one of the most common causes of unexpected brittleness and cracking in PBT parts.

What is the heat deflection temperature of PBT?

Unfilled PBT reaches an HDT of roughly 150 °C at 1.8 MPa. Adding 30% glass fiber pushes the HDT above 200 °C, which is why glass-filled grades dominate connectors and under-hood electrical parts. Flame-retardant versions reach UL94 V-0 while keeping much of this thermal performance.

How much does PBT shrink during molding?

Unfilled PBT shrinks about 1.2–2.0%, which is high compared with amorphous resins like PC and ABS. With 30% glass fiber, shrinkage falls to roughly 0.3–0.8% but becomes directional, higher along the flow direction. Always design with the specific grade's shrinkage data and keep wall sections consistent to limit warpage.

Why does PBT sometimes break or crack easily?

Brittleness usually traces back to moisture during processing, excessive shear at undersized gates, or sharp internal corners that concentrate stress. Dry the resin correctly, use adequate gate sizes, lower injection speed where shear is high, and add generous radii to load-bearing features to restore the material's normal toughness.

Looking for a Reliable PBT Injection Molding Partner?

Send your drawings and requirements — heat rating, flame-retardant class, tolerances — and we will recommend the right PBT grade, quote it, and include a free DFM analysis.

Shinzoft serves customers worldwide with custom PBT injection molding solutions from prototype to mass production. Explore the full range on our materials page.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com