LLDPE (Linear Low-Density Polyethylene) Injection Molding Supplier & Manufacturer

LLDPE (Linear Low-Density Polyethylene) is a linear polyethylene with short-chain branching and a density of 0.915–0.935 g/cm³. It delivers higher tensile strength, tear resistance, and puncture resistance than LDPE while keeping much of its flexibility, which makes it ideal for thin-wall containers, lids, flexible parts, and toys. Shinzoft provides OEM/ODM LLDPE injection molding from DFM and tooling through validated mass production.

Key Properties of LLDPE for Injection Molding

Higher Tensile Strength

Short-chain branching instead of long-chain branching gives LLDPE a tensile strength of 15–25 MPa — roughly 1.5 to 2 times that of LDPE at similar density — so thin sections hold up under real load.

Tear & Puncture Resistance

Notch and puncture resistance far exceed LDPE, which is why LLDPE dominates thin-wall lids, living hinges, and flexible parts that get pulled, pierced, or torn in service.

Environmental Stress Crack Resistance

Excellent ESCR for a polyethylene, so LLDPE resists cracking under long-term stress in contact with detergents, oils, and chemicals — a common failure mode for LDPE and HDPE.

Flexibility with Toughness

Modulus stays in the 250–450 MPa range, so parts remain flexible and soft-touch while withstanding impact and repeated flexing better than a softer LDPE grade would.

Technical Specifications of LLDPE

These values describe unfilled, general-purpose injection molding grades. LLDPE density and stiffness depend on comonomer type (butene, hexene, or octene), so a grade near 0.935 g/cm³ behaves noticeably stiffer than one near 0.915 g/cm³.

PropertyTypical ValueNotes
Density0.915–0.935 g/cm³Sits between LDPE and HDPE
Tensile Strength (Yield)15–25 MPaHigher than LDPE at comparable density
Flexural Modulus250–450 MPaFlexible yet tougher than LDPE
Elongation at Break>600%Very high ductility with strong tear resistance
Heat Deflection Temp (HDT, 1.8 MPa)45–60 °CSlightly better heat resistance than LDPE
Melting Point120–130 °CHigher than LDPE due to linear structure
Molding Shrinkage1.5–3.5 %Moderate; watch flow-direction variation
Water Absorption<0.01 %Non-hygroscopic, no drying needed
Dielectric Strength18–25 kV/mmGood insulation for flexible electrical parts

Applications of LLDPE Injection Molding

  • ✅ Thin-Wall Containers: Food tubs, takeaway bases, portion cups, and shallow trays where thinner walls are possible without cracking.
  • ✅ Lids & Closures: Snap-on lids, press-fit covers, tamper-evident caps, and flexible sealing lids that hinge and release thousands of times.
  • ✅ Flexible Components: Bellows, boots, grommets, liners, and live-flex inserts that must deform and recover without tearing.
  • ✅ Toys & Consumer Items: Durable toy components, play equipment parts, buckets, and household items built to survive rough handling.
  • ✅ Industrial & Agricultural: Bin liners, protective covers, tanks, and chemical-contact parts that need ESCR under sustained stress.

LLDPE Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / TimeNot required (non-hygroscopic; keep pellets clean and dry)
Melt Temperature190–240 °C
Mold Temperature20–50 °C
Injection Pressure60–110 MPa
Holding Pressure35–65 MPa
Typical Cycle Time15–45 s (depends on wall thickness)

LLDPE needs a somewhat higher melt temperature than LDPE because its linear structure is more viscous and less shear-thinning, but it delivers better melt strength and easier demolding as a result. That combination makes thin-wall and long-flow parts more forgiving than LDPE. Watch for flow-direction shrinkage differences on large flat lids, and add balanced cooling so the flatter, stiffer part does not twist on ejection.

Design & Tooling Considerations for LLDPE

  • Shrinkage allowance: Plan for 1.5–3.5% and check density. Grades near 0.935 g/cm³ shrink more and behave closer to HDPE than an octene grade near 0.915 g/cm³.
  • Thin-wall design: LLDPE's higher melt strength supports walls down to roughly 0.8–1.2 mm. This is where LLDPE earns its place over LDPE, which tears more easily in thin sections.
  • Gate and runner sizing: Use larger gates than for LDPE to manage the higher viscosity. Balanced multi-cavity runners keep fill pressure even and reduce warpage across cavities.
  • Living hinge design: LLDPE handles higher flex cycles than LDPE. Keep the hinge thin, orient the melt flow across the hinge line, and radius both faces to avoid stress concentration.
  • Lid flatness: On large lids, run symmetrical cooling and avoid gating at one edge. Uneven cooling plus directional shrinkage is the main cause of warp and poor sealing.

LLDPE vs Other Injection Molding Materials

LLDPE exists because LDPE could not keep up in thin sections. Against LDPE, it raises tensile strength, tear resistance, and ESCR while staying flexible, which lets designers reduce wall thickness and part weight. Against HDPE, LLDPE gives up some stiffness and chemical resistance but wins clearly on puncture toughness and stress crack resistance, and molds with better melt strength in long-flow parts. Against PP, LLDPE is softer, more flexible, and tougher at low temperature, while PP remains the choice for stiffness, heat resistance, and long-life living hinges.

Related Injection Molding Materials

Why Choose Our Factory for LLDPE Injection Molding

  • ISO 9001 Certified Quality: Verified incoming resin, controlled process parameters, and dimensional reports on every production lot.
  • 15+ Years of Experience: Established in 2010 with more than 1,000 customers and over 30 million parts produced from our Shenzhen and Huizhou facilities.
  • Free DFM Analysis: For thin-wall and lid projects we model fill balance, gate placement, and cooling symmetry before tooling, which is how warpage and short shots are avoided.
  • Fast Lead Time & No MOQ: With 50+ molding machines we ship most orders within 15 working days, and there is no minimum order quantity on new projects.

FAQs About LLDPE Injection Molding

What is the main difference between LLDPE and LDPE?

Molecular structure. LDPE has long-chain branching, while LLDPE has a linear backbone with short-chain branches. That linear structure raises tensile strength, tear resistance, puncture resistance, and ESCR, so LLDPE holds up better in thin walls and long-flow parts while still molding as a flexible polyethylene.

How thin can I design an LLDPE part?

Injection molded LLDPE walls can go down to roughly 0.8–1.2 mm depending on part size and flow length. LLDPE's better melt strength and toughness are what make those thin walls possible without tearing. Send us the geometry and we will confirm the minimum workable thickness during DFM review.

Is LLDPE better than LDPE for living hinges?

Yes, generally. LLDPE tolerates more flex cycles than LDPE before stress whitening or tearing appears, which makes it a good fit for snap lids and flexible closures. For very high cycle counts or hot environments, PP homopolymer still outperforms both and is the usual specification for long-life hinges.

What melt temperature does LLDPE injection molding need?

Typically 190–240 °C, with mold temperature around 20–50 °C. LLDPE is more viscous than LDPE because of its linear structure, so it needs a bit more heat and slightly larger gates. In return it delivers better melt strength and easier demolding, which suits thin-wall and long-flow parts.

Does LLDPE require drying before molding?

No. Like the rest of the polyethylene family, LLDPE is non-hygroscopic with water absorption below 0.01%, so it does not need drying. Keep pellets clean and dry during storage; only surface condensation from cold or damp storage needs a short low-temperature dry before molding.

Looking for a Reliable LLDPE Injection Molding Partner?

Upload your drawings and receive a quote with a free DFM analysis covering thin-wall limits, gating, and cooling balance.

Shinzoft serves customers worldwide with custom LLDPE injection molding solutions, and you can review the full range on our materials page.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com