Injection molding is a widely used manufacturing process for producing transparent plastic products, such as automotive light covers, electronic display screens, and daily consumer goods. However, during injection molding, various defects often occur on transparent plastic parts due to factors like material properties, mold design, and process parameters. These defects not only affect the appearance of the products but also reduce their mechanical properties and light transmittance. This article analyzes the common problems in injection molding of transparent plastic products and provides targeted solutions, aiming to improve the quality and yield of transparent plastic parts.

Common Defects and Their Causes in Injection Molding of Transparent Plastic Products
1.1 Silver Streaks
Silver streaks are linear or dendritic white marks on the surface of transparent plastic parts, which seriously damage the transparency and aesthetics.
- Main causes:
- Moisture in the raw materials: Transparent plastics like PMMA, PC, and PET are highly sensitive to moisture. If the materials are not fully dried before injection molding, the moisture will vaporize at high temperatures, forming bubbles that cause silver streaks.
- Entrapped air: During the injection molding process, if the mold exhaust system is poor or the injection speed is too fast, air will be entrapped in the melt and remain in the molded parts, leading to silver streaks.
- Poor material fluidity: When the melt fluidity is insufficient, the melt cannot fill the mold cavity evenly, resulting in shear stress and silver streaks at the flow front.
1.2 Yellowing and Discoloration
Transparent plastic parts may appear yellow or discolored after injection molding, which is mainly caused by thermal degradation of the materials.
- Main causes:
- Excessive processing temperature: If the barrel temperature or mold temperature is too high during injection molding, the transparent plastic will undergo thermal oxidation degradation, leading to yellowing. For example, PC is prone to degradation when the temperature exceeds 300℃.
- Long residence time of materials in the barrel: When the injection molding cycle is long or the machine is shut down unexpectedly, the materials stay in the barrel for too long, causing thermal degradation.
- Material contamination: Mixing different types of transparent plastics or adding impurities will cause discoloration of the molded parts.
1.3 Warpage and Deformation
Warpage and deformation are common dimensional defects of transparent plastic parts, which make the parts unable to meet the assembly requirements.
- Main causes:
- Uneven cooling: If the cooling system of the mold is uneven, the internal stress of the parts will be inconsistent during the cooling process, leading to warpage. For example, the cooling time of the thick-walled part is longer than that of the thin-walled part.
- Unreasonable mold structure: The design of the mold’s gate position, runner, and cooling system is unreasonable, which causes the melt to flow unevenly and the internal stress to concentrate.
- Improper ejection method: Excessive ejection force or unreasonable ejection structure will cause the parts to deform during ejection.
1.4 Bubble and Void
Bubbles and voids are holes or gaps inside the transparent plastic parts, which reduce the mechanical strength and light transmittance of the parts.
- Main causes:
- Moisture and volatile matter: As mentioned above, moisture in the materials vaporizes to form bubbles. In addition, some transparent plastics contain volatile additives, which will also volatilize at high temperatures to form bubbles.
- Insufficient injection pressure: If the injection pressure is too low, the melt cannot fill the mold cavity completely, resulting in voids.
- Poor mold filling: When the melt flow is unstable or the gate is too small, the melt cannot fill the cavity in time, leading to the formation of voids.

Solutions to Common Problems in Injection Molding of Transparent Plastic Products
2.1 Optimization of Material Handling
| Problem | Material Handling Method |
|---|---|
| Silver streaks caused by moisture | 1. Adopt high-efficiency drying equipment, such as dehumidifying dryers, to dry transparent plastics for 4-8 hours at 80-120℃ (PMMA) or 120-150℃ (PC). 2. Store materials in a dry and moisture-proof environment, and use moisture-proof packaging bags. |
| Yellowing caused by material degradation | 1. Select high-purity transparent plastic raw materials to reduce the content of impurities. 2. Avoid long-term storage of materials in the barrel, and clean the barrel regularly when changing materials. |
2.2 Optimization of Injection Molding Process Parameters
| Process Parameter | Adjustment Method for Common Defects |
|---|---|
| Barrel temperature | 1. For silver streaks: appropriately increase the barrel temperature to improve the fluidity of the melt and reduce the impact of moisture. 2. For yellowing: reduce the barrel temperature by 10-20℃ and shorten the residence time of materials in the barrel. |
| Injection speed | 1. For silver streaks: slow down the injection speed appropriately to avoid entrapping air. 2. For warpage: increase the injection speed properly to ensure the melt fills the cavity evenly. |
| Cooling time | 1. For warpage: extend the cooling time of the thick-walled part and optimize the cooling channel design to make the cooling uniform. 2. For production efficiency: on the premise of ensuring no deformation, appropriately shorten the cooling time. |
2.3 Improvement of Mold Design
- Optimize the exhaust system: Add exhaust slots or exhaust pins at the end of the mold cavity and the convergence of the melt flow to discharge the entrapped air smoothly. The width of the exhaust slot is generally 0.02-0.05mm.
- Rationalize the gate and runner design: For transparent plastic parts, choose a fan-shaped gate or a submarine gate to reduce the shear stress of the melt and avoid silver streaks. The runner should be as short and thick as possible to improve the fluidity of the melt.
- Improve the mold cooling system: Arrange the cooling channels evenly according to the structure of the parts, and use cooling water with a temperature of 40-80℃ to ensure uniform cooling of the parts.
2.4 Standardization of Operation and Equipment Maintenance
- Train operators to master the correct injection molding operation procedures, and regularly check the moisture content of materials, process parameters, and mold status.
- Maintain the injection molding machine regularly: Clean the barrel and screw to prevent material contamination and degradation; check the wear of the mold and repair or replace damaged parts in time.
- Use professional testing equipment: Detect the light transmittance, mechanical properties, and dimensional accuracy of the molded parts after production to ensure the product quality meets the requirements.
Conclusion
Injection molding of transparent plastic products is a complex process involving multiple factors such as materials, molds, and process parameters. The common problems in injection molding, such as silver streaks, yellowing, warpage, and bubbles, are closely related to material handling, process parameter setting, and mold design. By optimizing material drying, adjusting injection molding process parameters, improving mold design, and standardizing operation procedures, these defects can be effectively solved, thereby improving the quality and yield of transparent plastic parts. In actual production, manufacturers should combine the characteristics of specific transparent plastics and product requirements to formulate targeted injection molding solutions, and continuously summarize experience in production practice to promote the continuous improvement of injection molding technology for transparent plastic products.
FAQ
Q: What transparent plastics are commonly used in injection molding?
A: Common transparent plastics for injection molding include Polycarbonate (PC), Polymethyl Methacrylate (PMMA), Polyethylene Terephthalate (PET), and Cycloolefin Copolymer (COC). Each material has different properties, so the injection molding process parameters need to be adjusted accordingly.
Q: How to judge the moisture content of transparent plastic materials?
A: You can use a moisture meter to detect the moisture content of the materials. Generally, the moisture content of transparent plastics should be controlled below 0.02% to avoid defects caused by moisture. In addition, you can also observe the surface of the molded parts. If silver streaks appear, it is likely that the materials contain too much moisture.
Q: What should I do if the warpage of the parts is serious after injection molding?
A: First, check the cooling system of the mold to ensure uniform cooling; then, adjust the injection pressure and speed appropriately to make the melt fill the cavity evenly. If the warpage still cannot be solved, you need to optimize the mold structure, such as adding a reinforcing rib or changing the gate position.
