ASA (Acrylonitrile Styrene Acrylate) Injection Molding Supplier & Manufacturer

ASA (Acrylonitrile Styrene Acrylate) is an engineering thermoplastic built for long-term outdoor durability. It swaps ABS's UV-sensitive butadiene rubber for a saturated acrylate phase with no double bonds to break down, giving 5–10 times the weathering resistance of ABS along with excellent gloss retention and low static buildup that keeps dust off visible surfaces. That combination suits automotive exterior trim, outdoor equipment housings, satellite antennas, and garden tools. Shinzoft supplies OEM/ODM ASA injection molding from DFM and tooling to validated mass production.

Key Properties of ASA for Injection Molding

UV & Weather Resistance

The acrylate rubber contains no unsaturated double bonds, so UV light has nothing to attack. Color and gloss hold up over years of sun and rain, without the chalking or yellowing that limits ABS outdoors.

Surface Gloss & Appearance

ASA takes a deep, uniform gloss directly out of the tool and holds it far longer than most outdoor plastics. Molded-in color reduces the need for painting on visible exterior parts.

Low Static & Easy Clean

ASA builds up less surface charge than many plastics, so it attracts less dust and wipes clean easily — useful for instrument panels and appliance faces that must look sharp.

Toughness & Chemical Resistance

Impact behavior is comparable to ABS, with good resistance to dilute acids, alkalis, and many household chemicals. It also resists stress cracking better than general-purpose styrenics outdoors.

Technical Specifications of ASA

Values shown are typical for general-purpose, unfilled ASA grades and serve as design guidance.

PropertyTypical ValueNotes
Density1.05–1.07 g/cm³Close to ABS
Tensile Strength40–50 MPaComparable to ABS
Flexural Modulus2,000–2,500 MPaRigid, dimensionally stiff parts
Notched Izod Impact15–30 kJ/m²Grade-dependent; retains toughness when aged
Heat Deflection Temp (HDT, 1.8 MPa)90–105 °CTypically slightly higher than ABS
Glass Transition (Tg)~105 °CAmorphous, no sharp melting point
Molding Shrinkage0.4–0.7 %Low and stable
Dielectric Strength15–20 kV/mmGood electrical insulation

Applications of ASA Injection Molding

  • 🚗 Automotive Exterior: Grilles, mirror housings, roof rails, B-pillar trim, license-plate brackets
  • 🌦 Outdoor Equipment: Enclosures, control boxes, signage housings, camera and sensor covers
  • 📡 Satellite & Telecom: Antenna radomes, satellite dish housings, mounting shells
  • 🌿 Garden & Lawn: Tool housings, mower covers, watering-equipment bodies, outdoor furniture parts
  • 🏠 Building & Appliances: Window profiles, exterior appliance panels, vent covers, mailboxes

ASA Injection Molding Process Parameters

ParameterTypical Range
Drying Temperature / Time80–90 °C / 2–4 h
Melt Temperature230–270 °C
Mold Temperature50–80 °C
Injection Pressure60–120 MPa
Typical Cycle Time25–70 s (wall-thickness dependent)

ASA processes much like ABS, which makes grade swaps straightforward on existing tools. It is hygroscopic and must be dried at 80–90 °C for 2–4 hours to prevent splay on high-gloss exterior surfaces. A mold temperature of 50–80 °C is important for gloss uniformity, and good venting keeps weld lines from showing on visible faces. Because the material is typically used in natural-color or pigmented outdoor parts, running a slightly higher melt temperature helps flow and reduces flow-line visibility.

Design & Tooling Considerations for ASA

  • UV exposure zones: Specify UV-stabilized grades for parts facing direct sun, and keep wall thickness uniform to avoid uneven aging and color shift.
  • Gloss control: Mold texture is the primary driver of appearance; decide gloss level before cutting steel, since polishing an ASA tool later is expensive.
  • Gating: Position gates away from high-visibility faces and hide weld lines behind ribs or edges to preserve the clean exterior look.
  • Shrinkage: Plan on 0.4–0.7% with a consistent nominal value across cavities for dimensional repeatability.
  • Assembly and fastening: Use generous radii and avoid sharp notches, since stress concentrations reduce the long-term outdoor impact performance.

ASA vs Other Injection Molding Materials

ASA is best understood as the weatherable version of ABS injection molding — nearly identical processing and mechanical behavior, but far better UV and color stability. Where a part needs optical clarity rather than opacity, PMMA (acrylic) injection molding delivers higher light transmission and superior surface hardness. And where cost is the deciding factor and the part stays indoors, PS injection molding offers a lower-cost option with similar dimensional behavior.

Choose ASA when a visible part must survive sunshine, rain, and temperature swings without fading or chalking, and when you want to keep the easy processing and appearance of a styrenic material.

Related Injection Molding Materials

Why Choose Our Factory for ASA Injection Molding

  • ISO 9001 Certified Quality: Documented process control and inspection keep gloss, color, and dimensions consistent across production runs.
  • 15+ Years of Experience: Since 2010 we have delivered over 30 million parts to more than 1,000 customers worldwide.
  • Free DFM Analysis: We review gate placement, gloss goals, and UV-grade selection before tooling so outdoor parts perform as intended.
  • Fast Lead Time: Most orders ship within 15 working days, supported by 50+ machines across our Shenzhen and Huizhou plants.
  • No Minimum Order Quantity: We support prototype, pilot, and high-volume ASA programs with matched tooling and capacity.

FAQs About ASA Injection Molding

Why is ASA more weather-resistant than ABS?

ABS uses polybutadiene rubber, whose double bonds are attacked by UV and oxygen. ASA replaces that with a saturated acrylate rubber that has no double bonds to break, giving roughly 5–10 times the weathering life and far better color retention outdoors.

Does ASA need to be dried before molding?

Yes. ASA absorbs moisture, and undried resin produces splay and silver streaks that are especially obvious on glossy exterior parts. Dry at 80–90 °C for 2–4 hours and confirm moisture content before running.

Can ASA be molded with the same tool as ABS?

In most cases yes. The two materials share similar shrinkage (0.4–0.7%) and processing windows, so an ABS tool usually runs ASA with only minor parameter changes. Confirm gate and draft details during DFM if appearance is critical.

Is ASA suitable for automotive exterior parts?

Yes. ASA is a standard choice for grilles, mirror housings, and trim because it holds color and gloss through sun, rain, and temperature cycling. Molded-in color often removes the need for painting on these parts.

How does ASA compare with PMMA for outdoor use?

Both weather well. ASA is tougher and easier to process, while PMMA is transparent and harder on the surface. Choose ASA for pigmented, impact-resistant housings and PMMA for clear lenses and lighting covers.

Looking for a Reliable ASA Injection Molding Partner?

Send us your drawing and target gloss, and we will return a quote with a free DFM analysis. Tell us the outdoor exposure and volume, and we will confirm the right UV-stabilized grade.

Shinzoft serves customers worldwide with custom ASA injection molding solutions from DFM and tooling to validated mass production. Browse our injection molding materials for related options.

Get a Free Quote →
TYPE TO SEARCH

Tel:+86 0752-3336216
Email:Sales@shinzoft.com